Mule Utility Vehicles You will find the VIN on the top edge of the front bench seat base, just below the seat cushion. Subscription Preferences. Enter your email address so that we can find your existing information. Sorry, cannot submit. Invalid fields exist in below form.
If you are currently subscribed, check your email for a secure link. This will burn out the diodes in the electrical parts. Connecting Rod Twist — — — 0. Run the hoses inside the 2. Ownfrs Blue main harness. If it does not, replace the brake light switch. See each listing for international shipping options and costs.
If the surface is corroded, or if the blades are damaged, replace the impeller. Notice it differs from that of right side. If the coolant is brown, iron or steel parts are rusting.
If there is any damage to the rim, it must be replaced. The clearance may exceed the standard slightly, but it must not be less than the min- imum in order to avoid bearing seizure. We do it ourselves to help you do-it-yourself, and whatever your mechanical ability, the practical step-by-step explanations, linked to over photos, will help you get the job done right.
Regular servicing and maintenance of your Kawasaki Vulcan can help maintain its resale value, save you money, and make it safer to ride. Access this manual immediately on your internet browser on your mobile, desktop or tablet. Note the follow- ing. Be sure that all parts are put back in the correct sequence and facing the proper direction, and that all circlips and washers are properly in place.
Torque - Shift Pedal Mounting Bolt: 8. Special Tools Wheels Rims Front Wheel Removal Front Wheel Installation Rear Wheel Removal Rear Wheel Installation Wheel Inspection Spoke Inspection Rim Inspection Axle Inspection Balance Inspection Axial 0.
If there is any damage to the rim, it must be replaced. Adjust the tire air pressure according to the specifications if necessary. Air Pressure when cold Up to This can damage or warp the disc.
Place blocks under the wheel so that the disc does not touch the ground. Chain Slack — — — Standard Chain Make Enuma — A chain that breaks or jumps off the sprock- ets could snag on the engine sprocket or lock the rear wheel, severely damaging the motorcycle and causing it to go out of control.
Link Pin Outside Diameter 5. Standard: 5. If the bearing is removed, it will need to be replaced with a new one. T3: 1. R: Replacement Parts Disc Thickness 4. Disc Runout Not more than 0. Brake Fluid: Grade If you apply com- pressed air into the caliper, the piston may crush your hand or fingers. There is a flat washer [D] on each side of the hose fitting.
If the fluid level is lower than the lower level line, fill the reservoir to the upper level line [A] in the reservoir [B]. Air, however, is easily compressed. Never reuse old brake fluid. Do not use fluid from a container that has been left unsealed or that has been open for a long time. If it does not, adjust the rear brake cam lever angle. Shoe Lining Thickness 4.
Drum Inside Diameter If necessary, measure the oil level as follows. The slit [D] in the bushing must face toward the left or right. Replace them if necessary. If the spring of either fork leg is shorter than the service limit, it must be replaced. L: Apply a non-permanent locking agent. The front wheel should swing fully left and right from the force of gravity until the fork hits the stop.
Starter Lockout Switch 8. Turn Signal Relay Side Stand Switch 2. Water Temperature Switch 9. Battery Ignition Coils Horns Junction Box 4. Spark Plugs Fan Switch Front Brake Light Switch 5.
Ignition Switch 2. Water Temperature Switch 3. Radiator Fan 4. Fan Switch 5. Ignition Coils 6. Spark Plugs 7. Rear Brake Light Switch 8. Alternator Stator 9. Crankshaft Sensor Starter Motor Starter Lockout Switch 2. Front Brake Light Switch 3. Horns T1: 1. Junction Box 3. Turn Signal Relay 4. Battery 5. IC Igniter T1: 5. Learn and ob- serve all the rules below. This will burn out the diodes in the electrical parts. If any wiring is in poor condition, replace the damaged wiring. If the specific gravity is below 1.
If the battery is charged while still in- stalled, battery electrolyte may spill and corrode the frame or other parts of the motorcycle. To turn off the headlight of United States and Canada models disconnect the headlight connector.
0コメント